MOBIL MOBILSOL PM is a Synthetic Based Cleaner for Lubrication
Systems
Product Description -
Mobilsol PM is a
highly detergent and dispersant synthetic fluid which, when added to the oil in
hydraulic, paper machine or general circulation systems, will help to release
and hold in suspension gummy oil oxidation products and insoluble materials.
Efficient clean up of the system from deposits accumulated with time in
reservoirs and pipework can therefore be achieved leading to the recovery of
the system original operating efficiency and to improved equipment protection.
Applications -
Mobilsol PM should be
used in accordance with the following instructions or recommendation should be
sought from Mobil technical service:
Introduce Mobilsol PM
into a contaminated system progressively in 1% increments based on the total
volume of system, (maximum to be used 4%).
Circulate dirty
lubricant / Mobilsol PM mixture for 3-10 working days whilst regularly checking
the condition of all filters. Additional filtration equipment may be required
when proper operation of the system could be affected by the release of high
amounts of deposits. Oil condition monitoring can be of assistance to monitor
the level of deposits being picked up in the oil.
Drain the system
whilst hot and flush with a small volume (10% of the system volume or less) of
the new product being introduced.
Replace all filters
and cartridges etc. and fill up with the new circulation oil.
Where pump or bearing
manufacturers specify a maximum viscosity for a particular operation, the
change in viscosity caused by the addition of Mobilsol PM should be calculated
from blending tables. In some cases it may be necessary to blend Mobilsol PM
with a lower viscosity oil before adding it to the fluid in use.
Note:
Do not use Mobilsol PM
in N C machine tools or servo valve systems without special engineering
consideration. In any systems incorporating sensitive servo control valves even very small particles of dirt introduced with the solvent/fluid mixture or dislodged by it may interfere with the valve operation. Cleaning hydraulic systems incorporating servo valves must be carried out strictly in accordance with the manufacturers’ instructions.
consideration. In any systems incorporating sensitive servo control valves even very small particles of dirt introduced with the solvent/fluid mixture or dislodged by it may interfere with the valve operation. Cleaning hydraulic systems incorporating servo valves must be carried out strictly in accordance with the manufacturers’ instructions.
Mobilsol PM is
recommended for use for the following applications:
·
Clean up of oil
circulation systems in service: paper machine lubrication systems, hydraulic
systems,
open heating systems operating below 140°C, general circulation systems lubricating gears and bearings.
open heating systems operating below 140°C, general circulation systems lubricating gears and bearings.
·
In closed heating systems,
maximum operating temperatures of the fluid are dependent on the duration of
exposure to higher temperatures (which can vary due to the design of the system, flow rates, etc). Please
consult your original equipment manufacturer to ensure proper operation. In addition, the following
conditions are recommended: 1) Maintain turbulent flow through the heater with Reynolds number greater
than 10,000; 2) take steps (as directed by heater OEM) to avoid localised areas of high heat flux, which
can lead to locally high skin temperatures in the heater causing thermal degradation of the fluid; 3) nitrogen
blanketing to minimise exposure of the fluid to oxygen and formation of oxidised components.
exposure to higher temperatures (which can vary due to the design of the system, flow rates, etc). Please
consult your original equipment manufacturer to ensure proper operation. In addition, the following
conditions are recommended: 1) Maintain turbulent flow through the heater with Reynolds number greater
than 10,000; 2) take steps (as directed by heater OEM) to avoid localised areas of high heat flux, which
can lead to locally high skin temperatures in the heater causing thermal degradation of the fluid; 3) nitrogen
blanketing to minimise exposure of the fluid to oxygen and formation of oxidised components.
·
Clean up by brush or
dip of machine parts, gears, bearings
Looking for any
other schmierstoffe product
in MOBIL ENGINE
OIL & LUBRICANT or other Lubricant ?
Just give us a call.
Source URL:
Email: info@dm-schmierstoffservice.de
Contact No: +49 8106 3978728
Tags:
Mobil
Mobilsol Pm,Mobil schmierstoffe, Mobil lubricants, Mobil lubricant, Mobil
schmierstoff, Mobil oil, Mobil motor oil, Mobil Brake Fluid, Mobil Fluid
#Lubricants #MotorOil #EngineOil #CrudeOil #Grease
#HydraulicOil #SyntheticOil #CarOil #GearOill #Oil #Gas #HydraulicFluid
#BrakeFluid #RapeseedOil #TractorOil #CylinderOil #Lubricant
#IndustrialLubricants #Fette #MineralOil #TransmissionOil #Petronas #Kluber
#Meguin #Castrol
Comments
Post a Comment